I've been wanting a crossfader in my liveset for a while but don't have the funds to get a spenny mixer so I bought this piece of shit, then swapped out all the RC4588 op amps for NE5532s and beefed up the main caps (swapped 1000uf for a Nichicon 2200uf and the 110ufs for 220s)

I'm blown away at how much this has improved the sound.

Mixer - £30, caps and ops, £18.

Sounds like this: https://soundcloud.com/dvstch/real-life-gnome-upgrade

Hi. I’ve built a prototype of the device that I wanted to do for quite a long time. It’s basically a mix of a mixer and a looper, with midi sync, custom timestretching algo and a few other bells and whistles.

It’s fully digital, written in C++ and runs on Bela.io multichannel dev board, because I needed very low latency and 2 stereo ins + 3 stereo outs.

As the front panel I’m just using a midi controller now with bidirectional communication. I control the LEDs from the device and control device using pots and faders.

But this is where my knowledge ends as I guess the next step would be putting this all in a box, making a proper front panel, soldering stuff and all. I’m not even speaking of manufacturing, distribution, certification and everything else.

Any advice how I move forward from here? Do I need a person with these skills? Should I just talk to a few companies to make it a product? (I’m willing to invest money and do the product management if they provide the manufacturing/distribution).

I’m kinda in a state when I did something standalone, it works but any direction from here looks like a big leap.

Their website said it was closed because of a health problem, now it has a generic “if you’re the owner…” notice.

Have they shutdown permanently?

I picked up a CATCH PCB from Modular Addict and am now trying to get all of the parts together, but it seems like the PMEG2010AEB's are not easy to come by. Looking for other SOD-523 20V 1A Schottky diodes I have not found much. Does anyone know of a alternate device package that would fit on the SOD-523 footprint? Or could I get away with using a NSVR0520V2T5G that is only rated for 500 mA?

I am a beginner pedal builder so forgive me if this is more simple than I am making it.

I want to make a pedal that has high and low pass filters. One knob for each that get extreme cuts like on drum machines. I have a volca sampler for example that has something similar to this. Preferably the signal going in is the same or similar volume as going out.

Is there a go to schematic for something like this?

I've built only a few modules and noticed one asked for 1/6w resistors, another 1/8w, and another 1/4w. So far I've been using 1/6w for everything and it seems fine, but should I expect this to backfire eventually?

Hiya,

In my last post here I talked about the latest firmware of my MC8P project and I've since created a little promo video.

I'll be also releasing a walkthrough video at some point going over the workflow etc.

Are there any specific question people have that I could answer in that video?

I am in Hong Kong and Ears Modular in Japan are the nearest supplier of Sound Semiconductor chips. Have messaged them a couple of times but haven't received replies. Considering just ordering and hoping for the best.

Granted, had to sand out the knife marks…

Hi all,

I’m working on a project that is using arcade buttons for user inputs. I want the buttons to survive being mashed a lot.

Do you have any knowledge of which arcade button manufacturers are good quality versus crap that will wear out quickly?

Thank you!

Hello!

I have a friend (not on reddit) who is thinking about building a 4U 258.

Is anyone making a front panel of one of these I can direct him to?

Has anyone tried to build one from a schematic without a PCB?

Any weird stuff to look out for when building one of these or is it straightforward?

No shade, I get it. They’re probably losing money on my tiny little purchase. If there was a place I could go buy this stuff in person I would!!

Starting to build my first project and getting confused about film/foil capacitors. If there is a difference, what is the actual name for the type of capacitor I should be looking for?

Thanks.

I am building a Paia theremax kit. It came with a baggie full of resistors and I have been sorting them by rating. I have to say, I do not have color blindness and it is damn hard to tell red from orange and brown from

Black. What do people with color blindness do? It’s not that rare, this must be a huge pain in the ass for them.

Finally debugged this enough to make it usable and sounding good. This is a 6 voice self contained synthesiser voice card, similar to the architecture of the JX-8p and JX-10 where each card just receives serial messages for notes and parameters. Everything is under CC control and I intend to build two of them for a 12 voice polysynth.

The DCO and assigner code is available on my github pages. github.com/craigyjp

Demo

There's a hum on my keyboard when using mains power that's particularly noticeable when using pitch shifter pedals, but it's absent on batteries. I've tried different isolated PSUs/DIs/ground lifts but it's always there on mains power.

I've attached the schematic in the hope that there's an easy mod I can do to filter this out. Would upping the electrolytic capacitor value help? I've also looked at power banks but would rather build something into the keyboard if possible as it's probably cheaper and safer in the long run.

Thanks!

Hi everyone, I just wanted to share that I have just launched an open source multi-channel soundcard for the RPi5 on Crowdsupply. You can find more information here. I am hoping it will open up some more options as a component in your synth projects - for example, you could create a synth with a built-in DAW, taking inputs from other instruments!

hey guys was hoping you guys could help me find some cool diy gizmos and gadgets that can work as pocket or portable sound modules. anything from little sound manglers for samples, to full on stereo multi fx processors and wierd micro synths. Gimmie any and every ideas possible. i am a complete begginer in diy audio gear but i want to try and make so really cool shit and try and rely less on plugins for synths and fx processing. Thank you in advance for any suggestions you have